The optimum coefficients for the use of materials for combined beams in a wide range of loads are obtained in the article. The principles of designing and calculating the strength of Steel Reinforced Concrete slabs are outlined in accordance with SR 266.1325800.2016 ""Steel Reinforced Concrete Structures. Design rules"". Strength calculations are performed, the results of a numerical experiment are compared and analyzed. The optimal utilization factor of materials obtained in accordance with the specified regulatory document was established. The results obtained can be used in the design of combined beams of different cross-sections and spans. The purpose of this study is to find the optimum reinforcement of the floor beams. To strengthen the proposed installation of prestressed reinforcement in the lower girdle of the beam, which increases the strength and reduces the deflections of the beams. In such ceilings, the bending moment from external loads is distributed between the structural elements: the beam and the reinforced concrete overlap, in accordance with the ratio of the stiffnesses of these components. As a result of the study, the optimal diameters of prestressed reinforcement for steel beams by spans from 6 to 9 m were determined and for the calculated linear load from 5 to 30 kN/m. The proposed reinforcement option allows to increase bearing capacity, reduce deflections, reduce labor costs for building reconstruction, and also increase the reliability and durability of the structure.

Keywords: Steel reinforced concrete, floors, combined beams, profiled sheet, coefficient of use of materials

Passive detection sensors are widely spread in engineering-technical systems of information protection. During designing such systems, it may be difficult to calculate the coverage areas of infrared detectors. This is due to the fact that the problem of establishing a relationship between the theory of statistical detection and the choice of parameters for the equation of the maximum detection range is not considered in detail. In this regard, the task was to develop a method for applying the basic equation of passive location to calculate the coverage areas of infrared detectors. The calculation method is developed on the basis of the equation of the maximum range of the passive receiver. The study considered three models of the signal-to-noise ratio: a signal against a white noise background with fully known signal-to-noise parameters; detection of a signal whose phase and amplitude are unknown; and detection of a random signal against a noise background. As a result of the research, the conditions under which the passive signal detection formulas on the background of noise give correct results were found. Thus, the connection of the statistical theory of detection with the equation of the range of the passive emitter was established.

Keywords: information security, infrared detector, passive location, engineering and technical protection, the pyroelectric element

In is paper investigated and confirmed the Deposit of bentonite clay on the studied road section of Osh-Isfana. Osh-Isfana road is an international meaning road. The road is located in the Nookatsky district of Osh region of Kyrgyz Republic and connects the two regions and gives access to the territory of neighboring States – Tajikistan and Uzbekistan. Overestimation of the roadbed with moisture is an extremely dangerous phenomenon, since the strength of the pavement and the stability of the slopes of the mounds and excavations are greatly reduced. When designing the basis of the road on collapsible soils are equally important inside the event with the aim of reducing the likelihood of soaking the soil. The recommendations on the use of local building material as a waterproofing layer of the road structure, interrupting the movement of moisture, while ensuring the removal of water from rain and snow melt.

Keywords: slope, water-heat regime, sediment, moisture, waterproofing material, X-ray spectral analysis, shale clay, bentonite clay

the development of the best available technologies, in particular, the disinfection of waste water from meat processing plants is possible in meat clusters, of which the universities are an indispensable element. Disinfection of waste water from meat-processing plants from sanitary-indicative microorganisms, pathogenic enterobacteria and helminth eggs during the electroflotocoagulation method was investigated. The effect of disinfection from E. coli, eterobacteria and salmonella averaged 99%.

Keywords: meat-processing enterprises, sewage, disinfection, electro-flotocoagulation

The problem of distribution of compensating devices of consumers between separate nodes of the power system is considered in the article. The analytical model and the algorithm for optimizing reactive power compensation are presented. Criteria of optimality of reactive power compensation are singled out. The account is taken of poorly formalized, technological factors.

Keywords: Keywords reactive power compensation, multicriteria, information uncertainty, consumer compensating devices, analytical model, optimality criteria, normalized factors

In this article the relevance of development of the wood concrete meeting the modern requirements for an ecological component and energy efficiency is considered. Features of the mechanism of structurization at hydration of the cement knitting and organic filler with use of the X-ray diffraction analysis are shown. Indicators of concentration of basic elements in the cement test without organic filler are defined and at his existence. The comparative analysis of structure of steam solution of wood concrete and structure of solution from quick-hardening cement with use of data of a rastroelektronny microscope is carried out.

Keywords: Ivashchenko Y.G., Laushkina V. A., Timokhin D.K.

The paper proposes a description of the developed optical measuring set-up for the contactless recording and processing of measurement results for small spatial (linear and angular) displacements of control surfaces based on the use of laser technologies and optical interference methods. The proposed set-up is designed to solve all the arising measurement tasks in the study of the physical and mechanical properties of new materials and in the process of diagnosing the state of structural materials by acoustic active methods of nondestructive testing. The structure of the set-up, its constituent parts are described, and the features of construction and functioning during measurements are discussed. New technical solutions for the implementation of the components of the set-up under consideration are obtained. The proposed set-up is intended for use in instrumentation, mechanical engineering, shipbuilding, aviation, energy sector, etc.

Keywords: optical measuring complex, non-contact measurements, measurements of small spatial displacements, structural materials, diagnostics of the state

The actual problems of using various reinforced concrete enclosing structures during the construction of an industrial facility are considered. A detailed comparison is made of the amount of materials required for the construction of the roof structure by overlapping the beams and the shell panel of the LCL. Based on the results of the comparison and calculations, the analysis of the results obtained and conclusions on the rational choice of the roof support structure

Keywords: prefabricated reinforced concrete structures. roofing, materials, concrete. steel, shell panels, reinforced concrete vaulted structures, prestressed reinforcement, beams

The article describes the design solution for the device of enclosing rows of bored piles and pile-anchors, ensuring the stability of the walls of the pit in the construction of structures under construction and excluding their influence on the adjacent structures. The results of calculations of the enclosing series are presented..The article describes the design solution for the device of enclosing rows of bored piles and pile-anchors, ensuring the stability of the walls of the pit in the construction of structures under construction and excluding their influence on the adjacent structures. The results of calculations of the enclosing series are presented.

Keywords: pile a row, the CFA piles-anchors, the fence of the pit

Based on the results of theoretical and experimental studies at FGBAC FNAC VIM, we conducted a system analysis of the existing gravitational grain cleaning machines and developed a prototype of a gravity-pneumatic seed-seeding machine (VIM-3). His laboratory (preliminary) tests were carried out. The general view, constructive and techno logical scheme of the machine are presented. The prototype of a cleaning machine can purify wheat seeds up to 99.5% by feeding the processed material up to 2.5 t / h with an impurity content of more than 80%, which corresponds to the category of OS and ES of GOST R 52325-2005, as well as to international norms .

Keywords: System analysis of grain cleaning machines, gravity column, pneumatic assortment channel, specific metal consumption, productivity increase

In this paper we consider the problem of constructing a precise passability model by point cloud obtained from stereo cameras. To solve this problem, we used a hierarchical elevation map. The criterion for dividing cells into smaller ones was extended to take into account the cell's completeness with a limited field of view. The passability model was also supplemented with an algorithm for detecting step obstacles. The accuracy and completeness of the detection of obstacles and a free surface was calculated experimentally on dataset taken in real conditions. The result of the experiment shows that the proposed approach increases the number of detected obstacles without significant loss of accuracy.

Keywords: passability model, elevation map, obstacle detection, stereo vision, principal component analysis

The article describes the chemical composition of groundwater in the Rostov area. On the basis of sanitary and environmental assessment of the chemical composition of groundwater from wells, one of the areas of the South-Eastern part of the Rostov area, which are sources of water of the Egorlykskaya station, it was found that the concentration of hydrogen sulfide exceeds the MPC by about 1000 times. Analysis of methods of water purification from hydrogen sulfide, the main of which include: oxidation with molecular chlorine, sodium hypochlorite, hydrogen peroxide, showed the advantage of using the hydrogen peroxide. A new reactor design is proposed, which allows to increase the contact time of the treated water with the oxidant by hydrogen peroxide without increasing the size of the structure. This allows the maximum transfer of dissolved hydrogen sulfide in the solid phase.

Keywords: groundwater; hydrogen sulfide, purification, hydrogen peroxide, chemical reactor, economic efficiency

The complexity and high cost of multiplexing optical fiber sensors is still the main limitation for the widespread introduction of sensory systems, both distributed and quasi-distributed, and point-like. The article proposes a new multiplexing method that takes advantage of both broadband and two-frequency radio-photon multiplexing systems. The simplest broadband radiator is taken from the first, but a complicated and expensive system of spectrometry is not used to determine the central wavelength of fiber Bragg gratings. From the second, a recording system is used at the beat frequency between two components, but an expensive system for generating two- and polyharmonic probing systems is not used. The multiplexing parameter is determined by the frequency of separation between the transparency windows of a fiber Bragg grating, for example, with two phase π-shifts, which differs by a certain value for each of the sensors. The mechanism of modeling of gratings of the specified type is given, in principle the possibility of multiplexing of various number of sensors is shown. When using sensor networks built on the basis of passive optical, the number of multiplexed sensors can reach 256, with all sensors having the same Bragg wave of the wave, and can be combined into tree, bus and other topologies.

Keywords: fiber Bragg grating, phase inhomogeneity, fiber optic sensor, multiplexing, transparency window, frequency difference between transparency windows, beat frequency

Theoretical studies of the temperature distribution during laser heating of the TiO2 precursor film on the FTO/glass substrate have been carried out. The simulation was performed on the basis of a numerical solution of the heat equation in the Matlab program to determine the energy density of the laser radiation necessary for crystallization of TiO2. It was shown that on the surface of the TiO2 precursor the temperature reaches a maximum value at a time point of 133 ns with the Gaussian temporal form of the laser pulse. The optimum energy density for crystallization of the TiO2 precursor film with the nanosecond pulse duration is 1.3-1.6 J/cm2, when the film thickness temperature corresponds to 400-500 °C. The obtained results of the simulation are consistent with experimental studies.

Keywords: numerical simulation, laser heating, temperature distribution, TiO2 film, solar cell

The article presents the analysis of causes of accident of a water tower. Conducted examination of the structure showed the following: Water tower made in the form of welded sheet construction. Steel tank has a cylindrical shape, the diameter of the tank is 3020мм, cylindrical pole with a diameter of 1220mm and a height of 18m. The walls of the tower are made of sheet metal with a thickness of 4 mm, welded together back to back. On the East side there is a steel staircase made of 50х50х4 area with safety fence, made from steel strip -40х4. The lower part of the support diked soil with a height of 2.5 m. The tower has four stretch marks from the steel rope Ø12mm. The main causes of the accident was the deviation from a typical project in the manufacture of structural tower.

Keywords: tower, project, design,resistance, load