The way of а compиter assessment of qиality of the mix consisting of two and more components is stated. The algorithm for definition of factor of иniformity of mixing is based оп а clиstering of K-averages and realized in an applied Matlab package with иse of the graphic GUI interface. Check of this way proved possibility of its иse for an assessment of qиality of а miх.

Keywords: quality of а mix, uniformity of mixing, components, cluster

The article is devoted to the resistance accounts composite structures. We consider the output resolution of the system of equations for determining the stress-strain state of construction, consisting of a base in the form of hexagonal plates, rigidly connected to the base of a circular cylindrical shell.

Keywords: plate, shell, the strength, the composite structure.

Circuit features of the electronics module for avalanche photodiode signal read-out, created on a basis of the specialized analog IC, are considered. Measurement re-sults of characteristics and noise depending on signal source capacity are given.

Keywords: avalanche photo diode, readout electronic, charge sensitive amplifier, shaper, electronics module

The article is devoted to the resistance accounts composite structures. Examine the work of the external forces acting on the structure, consisting of a base in the form of hexagonal plates, rigidly connected to the base of a circular cylindrical shell.

Keywords: plate, shell, the strength, the composite structure.

Results of computer modeling intense the deformed condition of a design of road clothes of the lesovozny highway on vertical movings and tangents to tension by a method of final elements on the program PLAXIS complex are given. Deformation of constructive layers of road clothes occurs under the influence of loadings from a lesovozny road train. Results of researches of change of tangents of tension and vertical movings are given for a covering, the basis, a working layer of earth of a road bed.

Keywords: stone mastic asphalt, lesovozny road train, design of road clothes.

A design of the actuator, consisting of a thin layers of silicon dioxide and aluminum is proposed. There are calculations made of the response speed and heat dissipation of the actuator. By making the best selection of layer thicknesses and optimization stages of technological process, in particular the deep selective etching of silicon, the best performance on the angle of inclination of the actuator and the speed of the device could be achived. The greater the difference between the initial temperature and the heating temperature, the stronger the beam of the actuator is lowered to the plane of the silicon plate, and, therefore, less angle of elevation above the surface of the silicon plate. It is thus possible to control the angle of the beam by selecting the appropriate heater and voltage, providing the desired temperature. The design of the micromirror device based on the proposed actuator is provided. The developed design is based on the actuator and allows for controling the tilt of the mirror in a wide range.

Keywords: silicon, termoactuator, micromechanical systems, bimorph structure, micromirrors

This paper addresses the testing results of steel rods with grade A500 and A600, which used as a conventional reinforcement. It was investigated the strength properties of carbon and fiberglass sheets with different number of material layers. The results are compared with the data given in the quality certificates.

Keywords: fiberglass, carbon frp sheets, laminates, sheets of carbon and fiberglass, the ultimate load ,strength

The questions related to the study of various varying factors on the strength of normal sections in beams. Here's a program of research by one methodology designed to study the effect of the type and content of steel reinforcement and externally composite on the strength of normal sections that have not previously been investigated.

Keywords: Concrete, reinforced concrete, the percentage of reinforcement, carbon frp sheets, fiberglass, laminates

An analysis for the influence, of type and quantity of steel and composite reinforcement, on the normal cracks development, at different load levels, and by the maximum allowable deflection in beams. It was Found that throughout the load range, the reference beams are most cracked. The reduction degree in crack width depends on the strength and percentage of the steel reinforcement.

Keywords: concrete, reinforced concrete, steel, fiberglass, carbon fiber, laminate, maximum allowable crack width, load level, the development of cracks, the relative width

  Method of an automatic recognition of sleep events is described. The method is based on analysis of amplitude histograms that are built on each of registered channels. The method is designed for sleep events, distinctive feature of which is expressed amplitude change that appears simultaneously on several channels. For example, "General body movement" and "Limbs movement" events. But this is not limited; method can be applied to other events, for example "Snore". Algorithm can be divided into three stages: histograms building and analysis, vertical analysis, results processing.

Keywords: PSG, sleep events, histogram, detection algorithm

  The components of force plate signals, generated by cardiac activity, are investigated. The person stays in an ortograde posture, sit in the relaxed pose and in a pose at which the trunk keeps vertically and don’t contact with seatback. On the basis of a spectral approach features of power plate “Stabilan” indications and hardware-software complex «A multifunctional chair» are analyzed at inspection of the person holding set postures in different functional conditions (before and after physical activity). It is shown that change of vertical force (ballistogramm data) is an integrative signal. Manifestation of muscular components in force plate signals for an ortograde posture and a human pose sitting with vertical trunk are discussed.

Keywords: Force plate vertical signal, cardiac activity, posture stabilization

The article considers the problem of maximum flow of minimum cost finding in fuzzy dynamic transportation network. The relevance of the problem is in its wide practical application on the rail, air, sea and other roads in finding of routes of minimum cost. The feature of the problem statement is that fuzzy nature of the network parameters, such as arc capacities and costs is taken into account. It allows us to make decisions more sensitive to environmental changes. The dependence of network parameters from flow departure is also considered, that allows to introduce the notion "dynamic" network as opposed to "stationary-dynamic", examined in the literature. The algorithm for solving the described problem in fuzzy conditions is proposed. To illustrate the algorithm a numerical example is presented.

Keywords: dynamic network, maximum flow of minimum cost, fuzzy numbers, arc capacity, transit time

In this paper, a new simple and accurate hybrid table/analytical model of the MOSFET drain current based on the interpolation of table parameters is proposed. This new hybrid table model has an accuracy similar to the pure table models but requires no complex parameter extraction. The drain current in the hybrid model is calculated as the product of the analytical model current and the correction factor approximated by two-dimensional series.

Keywords: MOS-transistor, MOSFET parameters, cryogenic temperature, parametric identification

Briefly discussed the theoretical model of the spectrum of RR intervals and its changes depending on the processes taking place. Made a device for measuring cardiointervalogramms (CIG). Obtained from the renting of data, of varying duration and frequency shall be recorded for further processing. The analysis revealed that the resulting spectrum satisfies the conditions considered in the theoretical model, and can be further analyzed with fractal characteristics. Such an analysis is of great importance in the diagnosis of the patient directly to the duration of the therapeutic procedure for the optimization of both time and intensity exerted influence.

Keywords: CIG; fractal series; the spectrum of RR intervals

One of the most widespread endocrine diseases in the world is diabetes therefore its true diagnostics, and also diagnostics of its complications (encephalopathy, complications in cardiovascular system, etc.) is always actual. During carrying out research the analysis of psychological testing of examinees was carried out. Also in this work the attention is paid to application of methods of the statistical analysis for classification of EEG of patients by diabetic encephalopathy and healthy examinees. The most informative indicators of EEG reflecting cognitive functions of a brain were revealed. The interrelation of results of psychological testing and EEG analysis is established.

Keywords: electroencephalography, diabetic encephalopathy, discriminant analysis